| SMRT : NEW Low Cost Actuator/Damper Motor |
|
 |
The long anticipated SMRT actuators are Smart Tough and can cover almost 90% of all VAV applications with the ability to automatically recognize communication signals such as On/Off, Floating, 0-10VDC, 2-10 VDC, 4-20mA, PWM and Characterized Stroke.
Features:
- Status LEDs: ONE Tri-color status LED.
- Colors:Green for CW, Red for CCW, Yellow for Alarm
- Wiring-Termination: Removable 6-position Terminal block for all required power and interface signals.
- Manual Control switches: CW and CCW N.O. momentary switches for manual over and/or programming total travel for less than default 90°
- Programmable features: Direct-Reverse acting, Input type, Output type, Learn and Run modes.
- Typical Rotation: Default 90°, programmable any angular travel in “Learn” mode in to its Flash memory.
- Characterized Stroke: PWM Input-interface and output capabilities offered.
Specifications:
- Supply Voltage: 24 VAC ± 25%, 50/60 Hz
- Power consumption: 2.5 VA when internal motor energized. 0.1 VA motor off.
- Control Signals:
- ON/OFF
- Floating
- 0-10 VDC
- 2-10 VDC
- 0-5 VDC
- 4-20 mA
- Feedback Output Signals:
- Programmable:
- 0-10 VDC
- 2-10 VDC
- 0-5 VDC
- Torque: 125 lb-in (15 Nm)
- Direction of Rotation: Programmable for Direct and Reverse Acting.
- Dimensions: L: 110mm x W: 80mm x H: 25mm
For further information see SMRT - Data Sheet.
Click on Image to see larger view.
|
| M2 : Universal & Modular Networked Controllers |
|
 |
Description:
- 8 universal inputs with status LEDs (thermistor, 0-10 VDC, 4-20 mA, pulse and dry contact)
- 8 universal analog outputs, 0-10 VDC
- 8 virtual inputs for use as calculated variables
- 2 sets of Output Ports for 4 channel form-C relay plug-in card via (Model M2-R4) or Triac Output Modules (M2-T4)
- 7 years battery back up via lithium battery
- Logging for all input, output and virtual variables
- Flash Microprocessor: 16/32 bits. Operating system firmware can be remotely updated
- Future expansion Serial Flash Memory port (Model M2-ID Tag)
- Two serial Sub-LAN ports for hand held terminals (Model M2-HH) or zone temperature sensors Models WTS, WTS-A, WTS-D
- All input, output, and network communication circuits are optically isolated
- Built in 24 VAC power isolation transformer and unregulated 24 VDC power output for powering external I/O devices
- Labeled and color-coded removable terminal blocks for fast and accurate wiring
- Up to 1000 Controllers can be networked via RS485 low cost wiring
- Industrial cast aluminum designed housing for minimum external electrical interference
For further information see M2 - Data Sheet.
Click on Image to see larger view.
|
M2D : Universal Controller with 3-Thermistor Sensor Inputs, 2 AOs (0-10 VDC), 2 AIs (0-10 VDC) and 4 relay DOs |
 |
Description :
- 3 Thermistor Inputs
- 2 AOs (0-10 VDC)
- 2 AIs (0-10 VDC)
- 4 Relay (via M2-R4 plug-in module)
For further information see M2D - Data Sheet.
Click on Image to see larger view. |
M2DI : Digital Input Controller |
|
Description :
- 8 universal inputs with status LEDs (thermistor, 0-10 VDC, 4-20 mA, pulse and dry contact)
- 8 universal analog outputs, 0-10 VDC
- 16 Digital Inputs
For further information see M2DI - Data Sheet.
Click on Image to see larger view.
|
| M2V : Universal & Modular Networked VAV Controller (no plug in modules) |
 |
Description :
- All M2 capabilities but it is a dedicated universal VAV controller
- Wide range of control strategies for all pressure dependent terminal boxes: single, dual duct, staged electric or hydronic reheat, serial-parallel fans, auxiliary lighting control w/spare outputsiables
- Modular design for Main Damper, Auxiliary damper, HW modulating re-heat valve control
- Built in precision Flow Sensor (Model M2V-FS)
- Built in Discharge Air temperature sensor input terminal for maximum precision zone temperature control and modulation
- M2V can interface with any actuator Solidyne recommends: MF4E (Low cost, floating, no feedback signal), MF4D (position feedback) or MS4D (proportional input: 0-10 VDC, 2-10 VDC position feedback signal)
For further information see M2V - Data Sheet.
Click on Image to see larger view.
|
WTS-D : Wall mount Zone Temp Sensor with LED numerical 3 digit display and 7-bar LED graphics and light level sensor |
 |
Description :
- Built in 3-digit large character LED display
- Comfort level set and displayed by multicolor LEDs
- Built in ambient light level sensors can be used for lighting and temperature control
- Built in “UP, DOWN and ENTER” buttons utilizing solid state photo reflective sensors (no moving parts)
- ±0.5% accuracy thermistor type sensor (10KOhms)
- After hours occupancy programmable
- Dual RJ45 built in connectors for fast and easy wiring
- Labor saving, fast single screw mounting
For further information see WTS-D - Data Sheet.
Click on Image to see larger view. |
| WTS-A : Wall mount Zone Temp Sensor w/slide adjustable comfort set |
 |
Description:
- Same as WTS with built in occupant comfort setting via slide adjust
- Comfort set is programmable for adjustable temperature range
- Two RJ-45 and 3-wire screw terminals for wiring
For further information see WTS-A - Data Sheet.
Click on Image to see larger view. |
CT-100 : Universal Current Transducer with a Split Core Current Transformer that can measure up to 100 Amps |
|
Description:
- Universal Current Transducer with a Split Core Current Transformer
- can measure up to 100 Amps
- built-in DIP switch for setting the accuracy range for current values
of 0-2.5A, 0-10A, 0-20A, 0-50A, and 0-100A
- output of the device is 4mA at the low end of the range and 20 mA at the high
end.
For further information see CT-100 - Data Sheet.
Also available in 0-10v dc output - see CT-100V - Data Sheet.
Click on Image to see larger view.
|
